2.4GHz, 100Mbps, 3 Miles (EZBR-0214+)
Zoom image

2.4GHz, 100Mbps, 3 Miles (EZBR-0214+)

Item# EZBR-0214+

The EZ-Bridge® LT+ is a high power 25dBm (316mW) outdoor wireless bridge system operating in the 2.4GHz unlicensed frequency spectrum providing real world throughput up to 100 Mb/sec. It complies with the 802.11gn or 802.11an standards to insure interoperability. The EZ-Bridge® LT+ creates a transparent wireless bridge between two networks up to 3 miles apart with good line of sight. It supports VOIP, VPN, multiple MAC addresses and DHCP across the wireless link. It is the perfect plug and play solution for connecting the networks in two or more buildings, internet access sharing, remote video surveillance or remote network access. Multiple EZ-Bridge® LT+ units can be connected in a mesh configuration to allow interconnecting more than two sites.

With its password verification, MAC address authentication, SSID suppression and advanced WPA encryption, the system provides the best available wireless data security.

Installation is a snap because of the plug and play features which have been built into the system. Just install the antennas and plug in the power inserters. The units will automatically find their peer and create a secure wireless network link. If changes to the pre-configured settings are desired, they can be easily done thru the built-in web interface from any point on either side of the network. There are no drivers or software that needs to be loaded to the computer.

The EZ-Bridge® LT+ comes complete with all the electronics that are needed for a point to point wireless network bridge installation; including 2 powerful 14dBi 802.11gn or 16dBi 802.11an MIMO antennas with built-in high power electronics, Bracket Kits which accommodate pole or wall mounting, Cat5e rated POE (Power Over Ethernet) power inserters and 24VDC auto-ranging power supplies. Customer needs to supply CAT5 cabling between the power inserter and the antenna and between the power inserter and his computer, router or switch.

The EZBR-0516+ management interface is IPv6 enabled, https enabled. Logon username is fixed. The password can be changed, and there are no rules for password length or content.

  • $189.95
Data Rates2.4Ghz 802.11n: up to 300Mbps
2.4 GHz 802.11g: up to 54Mbps
StandardsIEEE802.11g/n, 802.11a/n, 802.3, 802.3u
Power RequirementsPower Supply: 100-240VAC 50/60Hz
EZ-Bridge® : 12VDC to 24VDC Passive PoE Average
Power Consumption: 4W
Regulatory CertificationsFCC Part 15 / UL
RF Frequency Band2400 ~ 2497 MHz 5100 ~ 5850 MHz
Modulation Technology802.11n: TDMA
802.11g: OFDM
802.11a: OFDM
Receive Sensitivity (Typical)802.11n: -90 dBm
802.11g: -75 dBm
802.11a: -75 dBm
Transmit Power25dBm 316mW
DC Connector Power OutInput Voltage @ Max 10W
Antenna2.4GHz 14dBi MIMO Panel Antenna, 35deg Beamwidth, >20dB front to back
Operation Mode - Bridge or RouterPoint to Point Bridge, Access Point, Access Point WDS, Client, Client WDS
Interface10/100Mbps RJ-45 LAN Port x 2
IP ConfigurationStatic or Auto configuration using DHCP Client
SecurityMAC Address Filtering, WEP/WPA encryption, Hide SSID in beacons, Layer 2 isolation
Management Configuration

Web-based configuration (HTTP)
Console configuration (SSH)
SNMP Protocol

Firmware UpgradeUpgrade firmware via web browser
Antenna Physical Dimensions (LxWxH)314mm x 187mm x 65mm 12.4” x 7.3” x 2.5”
Complete System Weight3 kg (7 lbs )
Operating Temperature-30°C to +70°C (-22°F to 158°F)

2 Year

    • Weight
      10 lbs
    • SKU